Scanning and repairing drive every boot: How to Fix Scanning and Repairing Drive Stuck Issue on Windows 10/11? Quick Patch Here. — Auslogics Blog

How to Fix Scanning and Repairing Drive Stuck Issue on Windows 10/11? Quick Patch Here. — Auslogics Blog

Contents

  • Why is Windows scanning and repairing drive on booting?
  • How to stop Windows from scanning and repairing the drive?
  • Method one: using Windows Error checking tool
  • Method two: checking drive status
  • Method three: running a CHKDSK scan in Safe Mode
  • Method four: running the Repair-Volume-DriveLetter command in Safe Mode

Among some of the most frequently reported Windows 10 errors is the error message that shows up on startup and says, “Scanning and repairing drive”. Sometimes, the error message gets stuck on the screen, preventing your PC from booting properly. Some users have even reported getting this error message every time they turn on their PC. Naturally, this can get quite annoying — but the problem is easily fixed.

From this article, find out why Windows is scanning and repairing your drive on booting and how to stop Windows from scanning and repairing the drive.

Why is Windows scanning and repairing drive on booting?

You will typically get the “Scanning and repairing drive” message when your computer hasn’t been properly switched off: due to a forced shutdown, a power failure, etc.

Why does it happen? When you are working on your PC, your hard disk and RAM are writing and reading data. If your computer shuts down unexpectedly, you may lose some of the data stored in RAM — in the worst-case scenario, this can even lead to hard disk damage. Thus, when you turn on your computer after an “improper” shutdown, Windows will automatically scan your driver, trying to fix the issues that occurred in the process.

Finally, we remind you that if you have a habit of performing forced shutdowns, it’s better to put an end to this practice so as to avoid potential startup errors — just like the one described here.

How to stop Windows from scanning and repairing the drive?

If you see the Windows scanning and repairing process is stuck or if you simply don’t have the time to wait for it to complete, you can bypass the automatic scanning and, instead, repair the drive manually, if needed.

If you are working in Windows Normal Mode, you can try using the Windows Error checking tool or checking the status of your drive.

On the other hand, if you can’t boot Windows, you can try running a CHKDSK scan in Safe Mode or using the Repair-Volume -DriveLetter command in Safe Mode.

Let’s go over the four error-fixing methods in more detail.

Method one: using Windows Error checking tool

One of the first things you can try is using the Windows Error checking tool to scan for and repair any potential issues. Here’s how to do that:

  • In the Taskbar, select File Explorer.
  • Go to This PC and expand Devices and drives.
  • Right-click on the drive you saw in the Windows “scan and repair” message and select Properties.
  • Go to Tools and, under Error checking, select Check.
  • If errors are revealed during the scanning process, a new window will pop up suggesting you repair the drive. Click Repair.
  • If no errors have been found, you will still have the option to scan and repair the drive — in the new window, choose Scan drive.
  • Finally, restart your PC and check if the problem has been resolved.

If this method hasn’t worked, you can try checking the status of your drive.

You can see if there are any problems with the drive and if it needs repairing by checking its status. Here’s what to do:

  • Go to Control Panel.
    • To open Control Panel, go to the Start menu and type “control panel” in the search bar, then select Control Panel.
  • Select View by Small icons and click Security and Maintenance.
  • Select Maintenance.
  • In Drive status, you will find a link that will let you repair the drive. Click this link. Windows will tell you not to bother if the drive is okay.

Your drive will now be scanned for potential errors, and, if any are found, they will be repaired.

Method three: running a CHKDSK scan in Safe Mode

A CHKDSK scan is a quick and easy way to check your computer drive for system file errors and repair any issues that may be found. If you have a problem booting into Windows, you will need to use the CHKDSK command in Safe Mode. Follow these steps:

  • Run Windows 10 in Safe Mode.
    • To do that, launch the Settings application (Win + I), click on Update & Security, then go to the Recovery tab once the Update & Security page opens.
    • Next, click on Restart Now under Advanced Startup.
    • Once your system restarts, click on Troubleshoot under Choose an Option.
    • Select Advanced Options, then choose Startup Settings.
    • Click on Restart, then select Safe Mode once your system reboots.
  • To run Windows 11 in Safe Mode:
    • Open the Settings app and click on Recovery on the System page.
    • Click on Restart Now next to Advanced Startup.
    • Once your PC restarts, follow the steps in the previous guide to open Windows 11 in Safe Mode.
  • Press the Win + R key combo on your keyboard to open Run.
  • Enter “cmd” and press Shift+Ctrl+Enter to run Command Prompt in administrator mode.
  • Type in “chkdsk x: /f” (where “x” is the name of the drive you plan to scan and repair) and press Enter.

When the scanning and repairing process is complete, restart your computer and see if the issues have disappeared. If they haven’t, try running the repair-Volume-DriveLetter command in Safe Mode.

Method four: running the Repair-Volume-DriveLetter command in Safe Mode

Here, you will be using PowerShell to run the Repair-Volume-DriveLetter command to scan for and fix potential drive errors. Here’s how to do that:

  • Start Windows 10 in Safe Mode.
  • In the search box, type “powershell” to open the menu. Right-click Windows PowerShell and choose to run it as an administrator.
  • Enter the following command: “repair-volume -driveletter x” (where “x” is the name of the drive you want to repair). Then press Enter.
  • When the scanning and repairing process is complete, restart your PC and check if the problem has been fixed.

Finally, in order to ensure smooth and error-free performance of your disk, you can use specialized software such as Auslogics Disk Defrag Pro that will help your drives run at maximum efficiency, optimize file placement on your hard drive and, overall, improve your PC experience.

What is a good defrag program? Definitely, it is a software that will safely make your PC work faster: when your registry or disk are defragged, the performance gets much better.

What other problems have you encountered after a forced shutdown of your PC? Share in the comments below.

Do you like this post? ?

Please rate and share it and subscribe to our newsletter!



88 votes,



average: 2.67 out of
5

Loading. ..

【Solved 2023】10 Ways to Fix Scanning and Repairing Drive Stuck

Scanning and repairing regularly get stuck when the PC is attempting to boot. It very well may be brought about by the PC being inaccurately closed down, or the hard drive may have bad sectors or numerous different reasons. A few Windows 10 users have detailed that the Windows scanning and repairing cycle stuck for minutes or even hours. Furthermore, when sometimes they power on PC, they receive the «scanning and repairing drive stuck» message. If you get the scanning and repairing drive blunder on your Windows 10, relax, you can fix it with the techniques in this guide.

  1. Part 1: Overview of Scanning and Repairing Drive Stuck
  2. Part 2: How Do I Fix Scanning and Repairing Drive Stuck in Windows 10?

    • Fix 1: Check the Drive Status
    • Fix 2: Use Windows Error Checking Tool
    • Fix 3: Wait for the Completion of Scanning and Repairing
    • Fix 4: Disable Automatic Repair
    • Fix 5: Disable Fast startup Feature
    • Fix 6: Disable Check Disk on Booting
    • Fix 7: Run SFC Utility
    • Fix 8: Enter Safe Mode and Run CHKDSK
    • Fix 9: Run System Restore
    • Fix 10: Reinstall System
  3. Bonus: Boot and Recover Data from Computer Stuck in Scanning and Repairing HOT
  4. FAQs about Scanning and Repairing

Part 1: Overview of Scanning and Repairing Drive Stuck

Scanning and repairing drives may become stuck for certain Windows 10 clients when they attempt to boot their PC; in some cases, it would even be stuck for a few minutes or maybe hours. Different reasons might have caused the «scanning and repairing drive stuck at 100» issue. For instance:

  • You didn’t close down your computer the right way, like a forced closure or a power loss during usage.
  • The hard drive may have bad sectors on it.
  • Your PC might be under a virus attack.
  • Your device drivers have incorrect configurations.

Part 2: How Do I Fix Scanning and Repairing Drive Stuck in Windows 10?

Fix 1: Check the Drive Status

If there are issues with the drive, Windows will identify it and permit you to sweep and fix it by looking at the drive status.

Step 1: From Control Panel, go to Security and Maintenance.

Step 2: Click Maintenance, and under Drive status, you might see issues recorded here and a link to fix them.

Fix 2: Use Windows Error Checking Tool

Step 1: Go to the File Explorer and explore Devices and Drives.

Step 2: Right-click the drive that Windows is scanning and repairing and click Properties.

Step 3: Open the Tools tab and snap the Check button under Error-checking.

Step 4: Windows will observe errors and then click Repair Drive to fix them.

Step 5: If no mistakes are found, the following screen prompts. Click Scan drive to fix it.

Step 6 : Reboot your PC and verify whether the scan and repair drive stuck issue is settled.

Fix 3: Wait for the Completion of Scanning and Repairing

What amount of time should scanning and repairing the drive require? That depends. Assuming there is a minor issue on the drive that cycle won’t take long. Nonetheless, it might need hours for the «Scanning and repairing drive» to finish if the drive is in poor condition.

Fix 4: Disable Automatic Repair

Step 1: Press the power button to turn on the PC and when you see the Windows logo, hold down the power button again to switch off the PC. Repeat it twice.

Step 2: Turn your PC on, and don’t interfere with it this time. Then, at that point, you will see your PC in WinRE.

Step 3: Go to Troubleshoot > Advanced options from the «Choose an option» screen.

Step 4: Open the Command Prompt and enter “bcdedit” and remember the values of «identifier» and «recoveryenabled.» Generally, it’s «{current}» and «Yes.»

Step 5: Disable Automatic Repair by entering bcdedit/set {current} recoveryenabled no.

Step 6 : Restart your PC.

Fix 5: Disable Fast Startup Feature

Step 1: Right-click the Start button and go to Search.

Step 2: Click on “Power Options” once you have opened Control Panel.

Step 3: Click on the option “Choose what the power buttons do.”

Step 4: Click «Change settings that are currently unavailable.»

Step 5: Untick the Turn on quick startup (suggested) option and save changes.

Fix 6: Disable Check Disk on Booting

Step 1: Boot your PC in Safe Mode and type “regedit” the Run dialog box.

Step 2: Go to the Session Manager and click BootExecute.

Step 3: Then, at that point, in the spring-up window, change the Value data to autocheckautochk/k:C * and tap OK.

Step 4: Restart your PC to check whether it tackled the Windows 10 scanning and repairing drive stuck at 100 issues.

Fix 7: Run SFC Utility

Step 1: Open command prompt as admin.

Step 2: Run “sfc/scannow” to check and get back the corrupted system files.

Step 3: Sfc utility will examine your framework for such files, and if found, it will restore them from the %WinDir%\System32\dllcache folder.

Fix 8: Enter Safe Mode and Run CHKDSK

Step 1: Press the power button to turn on the PC and when you see the Windows logo, hold down the power button again to switch off the PC. Repeat it twice.

Step 2: Turn your PC on, and don’t interfere with it this time. Then, at that point, you will see your PC in WinRE.

Step 3: Go to Troubleshoot > Advanced options from the «Choose an option» screen.

Step 4: Click Startup Settings, then tap Restart and press F5

Step 5: Open This PC, right-click the drive that scanning and repairing drive stuck at 0, then, at that point, pick «Properties >Tools> Check.

Fix 9: Run System Restore

Step 1: Press and hold the Power button to constrain the PC to close down multiple times, and you will enter Windows Recovery Environment.

Step 2: Next, go to Troubleshoot > Advanced options.

Step 3: From there, click “System Restore” and tap “Next” to pick a system restore point.

Step 4: Click “Finish” to proceed.

Fix 10: Reinstall System

Step 1: Go to Settings > Update and Security and click on Recovery.

Step 2: A message, inquiring you to whether switch applications to Windows Security will show up. Click “Yes.”

Step 3: The Fresh Start option will appear.

Step 4: Tap on the Get Started button and then the «Next» button.

Step 5: That will delete all the applications that are not associated with Windows 10.

Step 6: Click “Next” to download the most recent version of Windows 10. Install the Windows, and your scanning and repairing drive stuck at 10 percent issue will resolve.

Bonus: Boot and Recover Data from Computer Stuck in Scanning and Repairing

Hopefully, the above methods will help you fix the scanning and repairing stuck issue. However, there may be instances where the C drive (the system disk) is significantly damaged and you are unable to boot into Windows despite attempting all of the repairs. You’ll need bootable data recovery software like Tenorshare 4DDiG data recovery with bootable media to recover all of the files from the non-working PC.

Some highlights of the 4DDiG data recovery include:

  • Boot and recover data from crached computer
  • Compatible with over 1000 file types and file systems, including photos, video, documents, audios and others.
  • Support to extract data from flash drives, hard drives, memory cards, digital cameras, and camcorders, among other storage devices.
  • Recover any lost or deleted data from Windows/Mac
  • Our data recovery success rates are among the best in the industry, with data recovered from a variety of data loss circumstances.

To recover unbootable laptop with 4DDiG, prepare yourself with the following stuffs before data recovery from crash computer: another working computer, a blank USB drive of more than 1.5G or CD/DVD.

Free Download

For PC

Secure Download

Free Download

For MAC

Secure Download

Buy Now

Buy Now

  1. Connect USB drive and Select
  2. Launch 4DDiG software on your computer and get your USB flash drive well connected. Choose Recover from Crash Computer from the home interface and then click on Scan to proceed.

  3. Create a Bootable Drive
  4. Choose an external USB/DVD drive to create a bootable drive then click on Create. After a while, the bootable drive will be created successfully and then you can turn to your crashed computer to start data recovery.

  5. Boot Crashed Computer and Recover Data
  6. Insert the USB flash drive or CD/DVD drive into the crashed computer then restart your device. Afterwards, you would see the computer brand logo on the screen, then press the corresponding key until you get into your device’s BIOS settings.After you enter the BIOS, switch to the boot tab using the arrow keys and select boot device. Then your crashed system will start loading files and please wait patiently for the configuration. Now 4DDiG will be launched automatically and you can select a location to start recovering data.

FAQs about Scanning and Repairing

1. How long should scanning and repairing the drive take?

Assuming your PC is currently scanning and repairing drive how long, that interaction will take more than 2 hours, relying upon the size of your drive and problems found. It commonly quits refreshing around 10 or 11% and out of nowhere leaps to 100 when done.

2. How do I bypass scanning and repairing drive C?

To bypass scanning and repairing of drive C, boot your computer in safe mode and run the system file checker utility as mentioned above. That will help complete the system scanning and repairing.

3. How do I disable scanning and repairing drive C every time Windows 10 starts?

To disable scanning and repairing drive C, you can employ one of the following techniques:

  • Run a CHKDSK scan in Safe Mode
  • Use Windows Error-checking tool
  • Open Safe Mode and run the Repair-Volume-DriveLetter command
  • Check the drive status

Summary

Scanning and repairing drive stuck consistently recommends problems with your disk. The arrangements are visible: either fix the errors or let Windows skip them. Determine your issue and select the most suitable fix from above. We hope that one of the strategies above could be valuable to eliminate the error from your device. By the way, try Tenorshare 4DDiG to boot and recover data before fixing the issue.

Disk check is enabled when Windows starts

Category: Troubleshooting.

In this article, we will consider several ways to disable the hard disk (HDD) check, which runs every time you turn on or restart your computer.

The most common cause is that the system marks the hard drive as «dirty». This is due to improper shutdown of the computer, violations in the file system, or damage to the hard drive itself.

To fix this problem, do the following:

1. Run a full disk check.

Open «My Computer» => right click on the disk that is constantly checked => from the context menu select «properties» => then on the tab «service» click the button «Perform verification»

in the window that opens, check all the boxes and click « Launch «.

If the system disk was selected, you will be prompted to perform a check at the next system boot — we agree and restart the computer. We are waiting for the end of the verification process.
If the problem persists, go to the next item;

2. Disable disk check.

Press the key combination Win-R or Start => All Programs => Accessories => Run => enter command cmd -> press OK . In the window that opens, enter the command chkntfs / X C: (where C : is the name of the drive that is constantly being checked).

Check is now disabled. If you want to enable it again, you need to type the command chkntfs /D .

CHKNTFS — enable/disable hard disk check on reboot

Displays or changes the parameters of disk check during boot.

  • CHKNTFS volume: [. ..]
  • CHKNTFS /D
  • CHKNTFS /T[:time]
  • CHKNTFS /X volume: […]
  • CHKNTFS /C volume: […]

volume Specifies the drive letter (followed by a colon), mount point, or volume name.

/D — restores the default settings of the computer; all disks are checked at boot and CHKDSK runs when errors are encountered.
/T:time — changes the countdown AUTOCHK to the specified amount of time in seconds. If no time is specified, shows the current setting.
/X — Excludes the standard disk check on boot. Information about previously excluded drives is not saved.
/C — requests to perform a disk check on the next boot; if errors are found on the disk, run CHKDSK .

If no parameters are specified, CHKNTFS displays either the status of the error detection bit for the drive or checks for it at the next reboot.

Like this article? Share with friends!

How to disable chkdsk disk check on boot in Windows 10: 2 ways to undo

Over time, software and hardware errors accumulate on the hard drive. This leads to problems in the PC, braking, freezing. To fix bugs in Windows, there is a built-in chkdsk function that automatically scans the hard drive after turning on the PC. For most users, this interferes, takes time. Let’s try to figure out how to disable chkdsk disk check on boot in Windows 10.

CONTENT OF THE ARTICLE:

In what cases might this be needed?

The basic option chkdsk is available in any version of the OS, performs tasks to find, identify and remove errors in the file system. If the gadget functions with insufficient performance, this is most likely due to the presence of poorly readable memory sectors and lost combined elements. The utility is usually configured in automatic mode, it performs a check every time Windows starts.

Checking the integrity of the system and the correct operation of the hard drive are important, but it is obsessively turned on every time the gadget is turned on. This is not convenient for the PC owner. The constant launch of the utility can cause physical wear and tear of the hard drive associated with software problems. The user will need to identify the source of errors and correct the situation.

The user may wish to disable the chkdsk checker due to shortcomings that arise during its operation:

  • starting problems;
  • shortcomings in work;
  • unscheduled checks.

For correct operation of the utility, the user can disable automatic verification. The user can run the check through the settings at any time convenient for him. In addition, constant disk scanning leads to an increase in load.

How do I disable chkdsk on Windows 10 startup?

There are two ways to disable the HDD check utility: use the chkntfs utility or through the registry.

Using the chkntfs utility

The command is used to display or change the automatic check at device startup. You must have Administrator rights to use the tool. This option can be confirmed in the program settings. Disabling HDD check options via the command line is considered the easiest and most accessible for gadget owners.

You can cancel the automatic activation of the utility by doing the following:

  • Start Windows 10.
  • Open Start.
  • Type the word «command» in the query string.
  • Right click on the result.
  • Select «Run as Administrator».
  • Enter: chkntfs /x c. The letter «C» indicates the name of the drive that will be scanned. To perform a task on two or more disks, specify them in order, separated by commas.
  • Press Enter.

After completing all the steps, automatic scanning by the chkdsk verification program will be disabled.

Through the registry

Using the command line is considered a safer method than editing the registry. But advanced users can use this method.

In order to remove the automatic activation of the function, follow the instructions:

  • Start the system.
  • Press the key combination Win+R.
  • In the window that appears, type the «regedit» command.
  • Confirm the action by clicking «Ok».
  • After starting the registry, enter: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager.
  • In the «Edit multiline» window, select the parameter: «BootExecute».
  • Double click on it.
  • Add the name of a disc or several discs to the value. Be sure to include spaces between commands.
  • Press «Ok».

The user should remember that editing the registry can adversely affect the system. Therefore, it is preferable to use the first method to disable the automatic launch of the program. A radical way to disable the utility should be used in exceptional cases.

Problems after disabling chkdsk and how to resolve them

There are situations when you cannot disable the check program or after that the system crashes. Consider the main problems that arise in this situation.

PC stopped booting

If there is a problem with starting digital technology, this indicates a problem with the drive. Here you will need to check it on another working device, if necessary, replace it.

A technical failure of the hard drive may cause chkdsk to run spontaneously. The disk must be checked on a working computer. You may need to perform a factory reset. In this case, user data will be lost.

The command line does not respond to commands

The first signs of such an error are problems with system files or incorrect setting of environment variables. In the first case, the user needs to check the system files, if necessary, troubleshoot.